5 years agoregulator: Fix the logic to ensure new voltage setting in valid range
Axel Lin [Wed, 11 Apr 2012 12:53:58 +0000 (20:53 +0800)]
regulator: Fix the logic to ensure new voltage setting in valid range

commit f55205f4d4a8823a11bb8b37ef2ecbd78fb09463 upstream.

I think this is a typo.
To ensure new voltage setting won't greater than desc->max,
the equation should be desc->min + desc->step * new_val <= desc->max.

Signed-off-by: Axel Lin <>
Signed-off-by: Mark Brown <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoARM: 7414/1: SMP: prevent use of the console when using idmap_pgd
Colin Cross [Sat, 5 May 2012 19:58:13 +0000 (20:58 +0100)]
ARM: 7414/1: SMP: prevent use of the console when using idmap_pgd

commit fde165b2a29673aabf18ceff14dea1f1cfb0daad upstream.

Commit 4e8ee7de227e3ab9a72040b448ad728c5428a042 (ARM: SMP: use
idmap_pgd for mapping MMU enable during secondary booting)
switched secondary boot to use idmap_pgd, which is initialized
during early_initcall, instead of a page table initialized during
__cpu_up.  This causes idmap_pgd to contain the static mappings
but be missing all dynamic mappings.

If a console is registered that creates a dynamic mapping, the
printk in secondary_start_kernel will trigger a data abort on
the missing mapping before the exception handlers have been
initialized, leading to a hang.  Initial boot is not affected
because no consoles have been registered, and resume is usually
not affected because the offending console is suspended.
Onlining a cpu with hotplug triggers the problem.

A workaround is to the printk in secondary_start_kernel until
after the page tables have been switched back to init_mm.

Signed-off-by: Colin Cross <>
Signed-off-by: Russell King <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoARM: 7410/1: Add extra clobber registers for assembly in kernel_execve
Tim Bird [Wed, 2 May 2012 21:55:39 +0000 (22:55 +0100)]
ARM: 7410/1: Add extra clobber registers for assembly in kernel_execve

commit e787ec1376e862fcea1bfd523feb7c5fb43ecdb9 upstream.

The inline assembly in kernel_execve() uses r8 and r9.  Since this
code sequence does not return, it usually doesn't matter if the
register clobber list is accurate.  However, I saw a case where a
particular version of gcc used r8 as an intermediate for the value
eventually passed to r9.  Because r8 is used in the inline
assembly, and not mentioned in the clobber list, r9 was set
to an incorrect value.

This resulted in a kernel panic on execution of the first user-space
program in the system.  r9 is used in ret_to_user as the thread_info
pointer, and if it's wrong, bad things happen.

Signed-off-by: Tim Bird <>
Signed-off-by: Russell King <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoFix __read_seqcount_begin() to use ACCESS_ONCE for sequence value read
Linus Torvalds [Fri, 4 May 2012 21:46:02 +0000 (14:46 -0700)]
Fix __read_seqcount_begin() to use ACCESS_ONCE for sequence value read

commit 2f624278626677bfaf73fef97f86b37981621f5c upstream.

We really need to use a ACCESS_ONCE() on the sequence value read in
__read_seqcount_begin(), because otherwise the compiler might end up
reloading the value in between the test and the return of it.  As a
result, it might end up returning an odd value (which means that a write
is in progress).

If the reader is then fast enough that that odd value is still the
current one when the read_seqcount_retry() is done, we might end up with
a "successful" read sequence, even despite the concurrent write being

In practice this probably never really happens - there just isn't
anything else going on around the read of the sequence count, and the
common case is that we end up having a read barrier immediately

So the code sequence in which gcc might decide to reaload from memory is
small, and there's no reason to believe it would ever actually do the
reload.  But if the compiler ever were to decide to do so, it would be
incredibly annoying to debug.  Let's just make sure.

Signed-off-by: Linus Torvalds <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoasm-generic: Use __BITS_PER_LONG in statfs.h
H. Peter Anvin [Thu, 26 Apr 2012 18:45:16 +0000 (11:45 -0700)]
asm-generic: Use __BITS_PER_LONG in statfs.h

commit f5c2347ee20a8d6964d6a6b1ad04f200f8d4dfa7 upstream.

<asm-generic/statfs.h> is exported to userspace, so using
BITS_PER_LONG is invalid.  We need to use __BITS_PER_LONG instead.

This is kernel bugzilla 43165.

Reported-by: H.J. Lu <>
Signed-off-by: H. Peter Anvin <>
Acked-by: Arnd Bergmann <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agopercpu, x86: don't use PMD_SIZE as embedded atom_size on 32bit
Tejun Heo [Fri, 27 Apr 2012 17:54:35 +0000 (10:54 -0700)]
percpu, x86: don't use PMD_SIZE as embedded atom_size on 32bit

commit d5e28005a1d2e67833852f4c9ea8ec206ea3ff85 upstream.

With the embed percpu first chunk allocator, x86 uses either PAGE_SIZE
or PMD_SIZE for atom_size.  PMD_SIZE is used when CPU supports PSE so
that percpu areas are aligned to PMD mappings and possibly allow using
PMD mappings in vmalloc areas in the future.  Using larger atom_size
doesn't waste actual memory; however, it does require larger vmalloc
space allocation later on for !first chunks.

With reasonably sized vmalloc area, PMD_SIZE shouldn't be a problem
but x86_32 at this point is anything but reasonable in terms of
address space and using larger atom_size reportedly leads to frequent
percpu allocation failures on certain setups.

As there is no reason to not use PMD_SIZE on x86_64 as vmalloc space
is aplenty and most x86_64 configurations support PSE, fix the issue
by always using PMD_SIZE on x86_64 and PAGE_SIZE on x86_32.

v2: drop cpu_has_pse test and make x86_64 always use PMD_SIZE and
    x86_32 PAGE_SIZE as suggested by hpa.

Signed-off-by: Tejun Heo <>
Reported-by: Yanmin Zhang <>
Reported-by: ShuoX Liu <>
Acked-by: H. Peter Anvin <>
LKML-Reference: <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoxen/pci: don't use PCI BIOS service for configuration space accesses
David Vrabel [Fri, 4 May 2012 13:29:46 +0000 (14:29 +0100)]
xen/pci: don't use PCI BIOS service for configuration space accesses

commit 76a8df7b49168509df02461f83fab117a4a86e08 upstream.

The accessing PCI configuration space with the PCI BIOS32 service does
not work in PV guests.

On systems without MMCONFIG or where the BIOS hasn't marked the
MMCONFIG region as reserved in the e820 map, the BIOS service is
probed (even though direct access is preferred) and this hangs.

Acked-by: Jan Beulich <>
Signed-off-by: David Vrabel <>
[v1: Fixed compile error when CONFIG_PCI is not set]
Signed-off-by: Konrad Rzeszutek Wilk <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoxen/pte: Fix crashes when trying to see non-existent PGD/PMD/PUD/PTEs
Konrad Rzeszutek Wilk [Thu, 3 May 2012 20:14:14 +0000 (16:14 -0400)]
xen/pte: Fix crashes when trying to see non-existent PGD/PMD/PUD/PTEs

commit b7e5ffe5d83fa40d702976d77452004abbe35791 upstream.

If I try to do "cat /sys/kernel/debug/kernel_page_tables"
I end up with:

BUG: unable to handle kernel paging request at ffffc7fffffff000
IP: [<ffffffff8106aa51>] ptdump_show+0x221/0x480
Oops: 0000 [#1] SMP
.. snip..
RAX: 0000000000000000 RBX: ffffc00000000fff RCX: 0000000000000000
RDX: 0000800000000000 RSI: 0000000000000000 RDI: ffffc7fffffff000

which is due to the fact we are trying to access a PFN that is not
accessible to us. The reason (at least in this case) was that
PGD[256] is set to __HYPERVISOR_VIRT_START which was setup (by the
hypervisor) to point to a read-only linear map of the MFN->PFN array.
During our parsing we would get the MFN (a valid one), try to look
it up in the MFN->PFN tree and find it invalid and return ~0 as PFN.
Then pte_mfn_to_pfn would happilly feed that in, attach the flags
and return it back to the caller. 'ptdump_show' bitshifts it and
gets and invalid value that it tries to dereference.

Instead of doing all of that, we detect the ~0 case and just
return !_PAGE_PRESENT.

This bug has been in existence .. at least until 2.6.37 (yikes!)

Signed-off-by: Konrad Rzeszutek Wilk <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agosmsc95xx: mark link down on startup and let PHY interrupt deal with carrier changes
Paolo Pisati [Mon, 23 Apr 2012 04:05:20 +0000 (04:05 +0000)]
smsc95xx: mark link down on startup and let PHY interrupt deal with carrier changes

commit 07d69d4238418746a7b85c5d05ec17c658a2a390 upstream.

Without this patch sysfs reports the cable as present

flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier

while it's not:

flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link

Tested on my Beagle XM.

v2: added mantainer to the list of recipient

Signed-off-by: Paolo Pisati <>
Acked-by: Steve Glendinning <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoLinux 3.0.31
Greg Kroah-Hartman [Mon, 7 May 2012 16:02:36 +0000 (09:02 -0700)]
Linux 3.0.31

5 years agohfsplus: Fix potential buffer overflows
Greg Kroah-Hartman [Fri, 4 May 2012 19:09:39 +0000 (12:09 -0700)]
hfsplus: Fix potential buffer overflows

commit 6f24f892871acc47b40dd594c63606a17c714f77 upstream.

Commit ec81aecb2966 ("hfs: fix a potential buffer overflow") fixed a few
potential buffer overflows in the hfs filesystem.  But as Timo Warns
pointed out, these changes also need to be made on the hfsplus
filesystem as well.

Reported-by: Timo Warns <>
Acked-by: WANG Cong <>
Cc: Alexey Khoroshilov <>
Cc: Miklos Szeredi <>
Cc: Sage Weil <>
Cc: Eugene Teo <>
Cc: Roman Zippel <>
Cc: Al Viro <>
Cc: Christoph Hellwig <>
Cc: Alexey Dobriyan <>
Cc: Dave Anderson <>
Cc: Andrew Morton <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Linus Torvalds <>
5 years agosched: Fix nohz load accounting -- again!
Peter Zijlstra [Thu, 1 Mar 2012 14:04:46 +0000 (15:04 +0100)]
sched: Fix nohz load accounting -- again!

commit c308b56b5398779cd3da0f62ab26b0453494c3d4 upstream.
[ backported to 3.0 by Kerin Millar <>]

Various people reported nohz load tracking still being wrecked, but Doug
spotted the actual problem. We fold the nohz remainder in too soon,
causing us to loose samples and under-account.

So instead of playing catch-up up-front, always do a single load-fold
with whatever state we encounter and only then fold the nohz remainder
and play catch-up.

Reported-by: Doug Smythies <>
Reported-by: LesÅ=82aw Kope=C4=87 <>
Reported-by: Aman Gupta <>
Signed-off-by: Peter Zijlstra <>
Signed-off-by: Ingo Molnar <>
Cc: Kerin Millar <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agowl1251: fix crash on remove due to leftover work item
Grazvydas Ignotas [Thu, 26 Apr 2012 20:07:44 +0000 (23:07 +0300)]
wl1251: fix crash on remove due to leftover work item

commit 4c1bcdb5a3354b250b82a67549f57ac27a3bb85f upstream.

This driver currently leaves elp_work behind when stopping, which
occasionally results in data corruption because work function ends
up accessing freed memory, typical symptoms of this are various
worker_thread crashes. Fix it by cancelling elp_work.

Signed-off-by: Grazvydas Ignotas <>
Signed-off-by: John W. Linville <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agowl1251: fix crash on remove due to premature kfree
Grazvydas Ignotas [Thu, 26 Apr 2012 20:07:43 +0000 (23:07 +0300)]
wl1251: fix crash on remove due to premature kfree

commit 328c32f0f85467af5a6c4c3289e168d9ad2555af upstream.

Currently SDIO glue frees it's own structure before calling
wl1251_free_hw(), which in turn calls ieee80211_unregister_hw().
The later call may result in a need to communicate with the chip
to stop it (as it happens now if the interface is still up before
rmmod), which means calls are made back to the glue, resulting in
freed memory access.

Fix this by freeing glue data last.

Signed-off-by: Grazvydas Ignotas <>
Signed-off-by: John W. Linville <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agortlwifi: Fix oops on unload
Larry Finger [Fri, 20 Apr 2012 02:39:06 +0000 (21:39 -0500)]
rtlwifi: Fix oops on unload

commit 44eb65cfd8da4b9c231238998729e858e963a980 upstream.

Under some circumstances, a PCI-based driver reports the following OOPs:

Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Oops: 0000 [#1] SMP
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Pid: 19627, comm: rmmod
Not tainted 3.2.9-2.fc16.x86_64 #1 LENOVO 05962RU/05962RU
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP:
0010:[<ffffffffa0418d39>]  [<ffffffffa0418d39>]
rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Process rmmod (pid:
19627, threadinfo ffff880050262000, task ffff8801156d5cc0)
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Stack:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  0000000000000002
ffff8801176c2540 ffff880050263ca8 ffffffffa03348e7
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  0000000000000282
0000000180150014 ffff880050263fd8 ffff8801176c2810
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  ffff880050263bc8
ffffffff810550e2 00000000000002c0 ffff8801176c0d40
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Call Trace:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  [<ffffffffa03348e7>]
_rtl_pci_rx_interrupt+0x187/0x650 [rtlwifi]
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Code: ff 09 d0 89 07 48
83 c4 08 5b 5d c3 66 0f 1f 44 00 00 55 48 89 e5 53 48 83 ec 08 66 66
66 66 90 40 84 f6 89 d3 74 13 84 d2 75 57 <8b> 07 48 83 c4 08 5b 5d c1
e8 1f c3 0f 1f 00 84 d2 74 ed 80 fa
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP
[<ffffffffa0418d39>] rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  RSP <ffff880050263b58>
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] CR2: 00000000000006e0
Mar 19 08:14:35 kvothe kernel: [ 6584.646491] ---[ end trace
8636c766dcfbe0e6 ]---

This oops is due to interrupts not being disabled in this particular path.

Reported-by: Dave Airlie <>
Tested-by: Dave Airlie <>
Signed-off-by: Larry Finger <>
Signed-off-by: John W. Linville <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agomac80211: fix AP mode EAP tx for VLAN stations
Felix Fietkau [Sun, 29 Apr 2012 13:44:16 +0000 (15:44 +0200)]
mac80211: fix AP mode EAP tx for VLAN stations

commit 66f2c99af3d6f2d0aa1120884cf1c60613ef61c0 upstream.

EAP frames for stations in an AP VLAN are sent on the main AP interface
to avoid race conditions wrt. moving stations.
For that to work properly, sta_info_get_bss must be used instead of
sta_info_get when sending EAP packets.
Previously this was only done for cooked monitor injected packets, so
this patch adds a check for tx->skb->protocol to the same place.

Signed-off-by: Felix Fietkau <>
Signed-off-by: John W. Linville <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoipw2200: Fix race condition in the command completion acknowledge
Stanislav Yakovlev [Thu, 19 Apr 2012 19:55:09 +0000 (15:55 -0400)]
ipw2200: Fix race condition in the command completion acknowledge

commit dd447319895d0c0af423e483d9b63f84f3f8869a upstream.

Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution.  Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:

Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.

After that you need to reload the driver to get it working again.

This bug occurs during roaming (reported by Sam Varshavchik)
and machine booting (reported by Tom Gundersen and Mads Kiilerich)

This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.

Signed-off-by: Stanislav Yakovlev <>
Signed-off-by: John W. Linville <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoi2c: pnx: Disable clk in suspend
Roland Stigge [Wed, 4 Apr 2012 08:34:37 +0000 (10:34 +0200)]
i2c: pnx: Disable clk in suspend

commit 6c557cfee08751d22aed34840f389b846f0f4508 upstream.

In the driver's suspend function, clk_enable() was used instead of
clk_disable(). This is corrected with this patch.

Signed-off-by: Roland Stigge <>
Reviewed-by: Arnd Bergmann <>
[wsa: reworded commit header slightly]
Signed-off-by: Wolfram Sang <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agolibata: skip old error history when counting probe trials
Lin Ming [Thu, 3 May 2012 14:15:07 +0000 (22:15 +0800)]
libata: skip old error history when counting probe trials

commit 6868225e3e92399068be9a5f1635752d91012ad5 upstream.

Commit d902747("[libata] Add ATA transport class") introduced
ATA_EFLAG_OLD_ER to mark entries in the error ring as cleared.

But ata_count_probe_trials_cb() didn't check this flag and it still
counts the old error history. So wrong probe trials count is returned
and it causes problem, for example, SATA link speed is slowed down from
3.0Gbps to 1.5Gbps.

Fix it by checking ATA_EFLAG_OLD_ER in ata_count_probe_trials_cb().

Signed-off-by: Lin Ming <>
Signed-off-by: Jeff Garzik <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agohwmon: (coretemp) fix oops on cpu unplug
Kirill A. Shutemov [Mon, 30 Apr 2012 13:18:01 +0000 (09:18 -0400)]
hwmon: (coretemp) fix oops on cpu unplug

commit b704871124b477807966f06789c2b32f2de58bf7 upstream.

coretemp tries to access core_data array beyond bounds on cpu unplug if
core id of the cpu if more than NUM_REAL_CORES-1.

BUG: unable to handle kernel NULL pointer dereference at 000000000000013c
IP: [<ffffffffa00159af>] coretemp_cpu_callback+0x93/0x1ba [coretemp]
PGD 673e5a067 PUD 66e9b3067 PMD 0
Oops: 0000 [#1] SMP
CPU 79
Modules linked in: sunrpc cpufreq_ondemand acpi_cpufreq freq_table mperf bnep bluetooth rfkill ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter nf_conntrack_ipv4 nf_defrag_ipv4 ip6_tables xt_state nf_conntrack coretemp crc32c_intel asix tpm_tis pcspkr usbnet iTCO_wdt i2c_i801 microcode mii joydev tpm i2c_core iTCO_vendor_support tpm_bios i7core_edac igb ioatdma edac_core dca megaraid_sas [last unloaded: oprofile]

Pid: 3315, comm: set-cpus Tainted: G        W    3.4.0-rc5+ #2 QCI QSSC-S4R/QSSC-S4R
RIP: 0010:[<ffffffffa00159af>]  [<ffffffffa00159af>] coretemp_cpu_callback+0x93/0x1ba [coretemp]
RSP: 0018:ffff880472fb3d48  EFLAGS: 00010246
RAX: 0000000000000124 RBX: 0000000000000034 RCX: 00000000ffffffff
RDX: 0000000000000000 RSI: 0000000000000046 RDI: 0000000000000246
RBP: ffff880472fb3d88 R08: ffff88077fcd36c0 R09: 0000000000000001
R10: ffffffff8184bc48 R11: 0000000000000000 R12: ffff880273095800
R13: 0000000000000013 R14: ffff8802730a1810 R15: 0000000000000000
FS:  00007f694a20f720(0000) GS:ffff88077fcc0000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 000000000000013c CR3: 000000067209b000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process set-cpus (pid: 3315, threadinfo ffff880472fb2000, task ffff880471fa0000)
 ffff880277b4c308 0000000000000003 ffff880472fb3d88 0000000000000005
 0000000000000034 00000000ffffffd1 ffffffff81cadc70 ffff880472fb3e14
 ffff880472fb3dc8 ffffffff8161f48d ffff880471fa0000 0000000000000034
Call Trace:
 [<ffffffff8161f48d>] notifier_call_chain+0x4d/0x70
 [<ffffffff8107f1be>] __raw_notifier_call_chain+0xe/0x10
 [<ffffffff81059d30>] __cpu_notify+0x20/0x40
 [<ffffffff815fa251>] _cpu_down+0x81/0x270
 [<ffffffff815fa477>] cpu_down+0x37/0x50
 [<ffffffff815fd6a3>] store_online+0x63/0xc0
 [<ffffffff813c7078>] dev_attr_store+0x18/0x30
 [<ffffffff811f02cf>] sysfs_write_file+0xef/0x170
 [<ffffffff81180443>] vfs_write+0xb3/0x180
 [<ffffffff8118076a>] sys_write+0x4a/0x90
 [<ffffffff816236a9>] system_call_fastpath+0x16/0x1b
Code: 48 c7 c7 94 60 01 a0 44 0f b7 ac 10 ac 00 00 00 31 c0 e8 41 b7 5f e1 41 83 c5 02 49 63 c5 49 8b 44 c4 10 48 85 c0 74 56 45 31 ff <39> 58 18 75 4e eb 1f 49 63 d7 4c 89 f7 48 89 45 c8 48 6b d2 28
RIP  [<ffffffffa00159af>] coretemp_cpu_callback+0x93/0x1ba [coretemp]
 RSP <ffff880472fb3d48>
CR2: 000000000000013c

Signed-off-by: Kirill A. Shutemov <>
Signed-off-by: Guenter Roeck <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agohwmon: (coretemp) Increase CPU core limit
Guenter Roeck [Tue, 1 May 2012 15:15:42 +0000 (08:15 -0700)]
hwmon: (coretemp) Increase CPU core limit

commit bdc71c9a87b898e4c380c23b2e3e18071312ecde upstream.

CPU core ID is used to index the core_data[] array. The core ID is, however, not
sequential; 10-core CPUS can have a core ID as high as 25. Increase the limit to
32 to be able to deal with current CPUs.

Signed-off-by: Guenter Roeck <>
Acked-by: Jean Delvare <>
Acked-by: Durgadoss R <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoefivars: Improve variable validation
Matthew Garrett [Thu, 3 May 2012 20:50:46 +0000 (16:50 -0400)]
efivars: Improve variable validation

commit 54b3a4d311c98ad94b737802a8b5f2c8c6bfd627 upstream.

Ben Hutchings pointed out that the validation in efivars was inadequate -
most obviously, an entry with size 0 would server as a DoS against the
kernel. Improve this based on his suggestions.

Signed-off-by: Matthew Garrett <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoefi: Validate UEFI boot variables
Matthew Garrett [Mon, 30 Apr 2012 20:11:30 +0000 (16:11 -0400)]
efi: Validate UEFI boot variables

commit fec6c20b570bcf541e581fc97f2e0cbdb9725b98 upstream.

A common flaw in UEFI systems is a refusal to POST triggered by a malformed
boot variable. Once in this state, machines may only be restored by
reflashing their firmware with an external hardware device. While this is
obviously a firmware bug, the serious nature of the outcome suggests that
operating systems should filter their variable writes in order to prevent
a malicious user from rendering the machine unusable.

Signed-off-by: Matthew Garrett <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoefivars: fix warnings when CONFIG_PSTORE=n
Tony Luck [Tue, 2 Aug 2011 22:08:30 +0000 (15:08 -0700)]
efivars: fix warnings when CONFIG_PSTORE=n

commit b728a5c806fb36f9adebf2a862bbd015e074afca upstream.

drivers/firmware/efivars.c:161: warning: ‘utf16_strlen’ defined but not used
utf16_strlen() is only used inside CONFIG_PSTORE - make this "static inline"
to shut the compiler up [thanks to hpa for the suggestion].

drivers/firmware/efivars.c:602: warning: initialization from incompatible pointer type
Between v1 and v2 of this patch series we decided to make the "part" number
unsigned - but missed fixing the stub version of efi_pstore_write()

Acked-by: Matthew Garrett <>
Acked-by: Mike Waychison <>
Signed-off-by: Tony Luck <>
[took the static part of the patch, not the pstore part, for 3.0-stable,
to fix the compiler warning we had - gregkh]
Signed-off-by: Greg Kroah-Hartman <>
5 years agoefivars: String functions
Mike Waychison [Thu, 21 Jul 2011 20:57:57 +0000 (16:57 -0400)]
efivars: String functions

commit a2940908391f3cee72e38769b30e829b22742b5b upstream.

Fix the string functions in the efivars driver to be called utf16_*
instead of utf8_* as the encoding is utf16, not utf8.

As well, rename utf16_strlen to utf16_strnlen as it takes a maxlength
argument and the name should be consistent with the standard C function
names.  utf16_strlen is still provided for convenience in a subsequent

Signed-off-by: Mike Waychison <>
Signed-off-by: Tony Luck <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoefi: Add new variable attributes
Matthew Garrett [Mon, 30 Apr 2012 20:11:29 +0000 (16:11 -0400)]
efi: Add new variable attributes

commit 41b3254c93acc56adc3c4477fef7c9512d47659e upstream.

More recent versions of the UEFI spec have added new attributes for
variables. Add them.

Signed-off-by: Matthew Garrett <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoSCSI: libsas: fix false positive 'device attached' conditions
Dan Williams [Tue, 20 Mar 2012 17:50:27 +0000 (10:50 -0700)]
SCSI: libsas: fix false positive 'device attached' conditions

commit 7d1d865181185bdf1316d236b1b4bd02c9020729 upstream.

Normalize phy->attached_sas_addr to return a zero-address in the case
when device-type == NO_DEVICE or the linkrate is invalid to handle
expanders that put non-zero sas addresses in the discovery response:

 sas: ex 5001b4da000f903f phy02:U:0 attached: 0100000000000000 (no device)
 sas: ex 5001b4da000f903f phy01:U:0 attached: 0100000000000000 (no device)
 sas: ex 5001b4da000f903f phy03:U:0 attached: 0100000000000000 (no device)
 sas: ex 5001b4da000f903f phy00:U:0 attached: 0100000000000000 (no device)

Reported-by: Andrzej Jakowski <>
Signed-off-by: Dan Williams <>
Signed-off-by: James Bottomley <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoSCSI: libsas: fix sas_find_bcast_phy() in the presence of 'vacant' phys
Thomas Jackson [Sat, 18 Feb 2012 02:33:10 +0000 (18:33 -0800)]
SCSI: libsas: fix sas_find_bcast_phy() in the presence of 'vacant' phys

commit 1699490db339e2c6b3037ea8e7dcd6b2755b688e upstream.

If an expander reports 'PHY VACANT' for a phy index prior to the one
that generated a BCN libsas fails rediscovery.  Since a vacant phy is
defined as a valid phy index that will never have an attached device
just continue the search.

Signed-off-by: Thomas Jackson <>
Signed-off-by: Dan Williams <>
Signed-off-by: James Bottomley <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoARM: 7403/1: tls: remove covert channel via TPIDRURW
Will Deacon [Fri, 27 Apr 2012 11:45:07 +0000 (12:45 +0100)]
ARM: 7403/1: tls: remove covert channel via TPIDRURW

commit 6a1c53124aa161eb624ce7b1e40ade728186d34c upstream.

TPIDRURW is a user read/write register forming part of the group of
thread registers in more recent versions of the ARM architecture (~v6+).

Currently, the kernel does not touch this register, which allows tasks
to communicate covertly by reading and writing to the register without
context-switching affecting its contents.

This patch clears TPIDRURW when TPIDRURO is updated via the set_tls
macro, which is called directly from __switch_to. Since the current
behaviour makes the register useless to userspace as far as thread
pointers are concerned, simply clearing the register (rather than saving
and restoring it) will not cause any problems to userspace.

Signed-off-by: Will Deacon <>
Signed-off-by: Russell King <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoautofs: make the autofsv5 packet file descriptor use a packetized pipe
Linus Torvalds [Sun, 29 Apr 2012 20:30:08 +0000 (13:30 -0700)]
autofs: make the autofsv5 packet file descriptor use a packetized pipe

commit 64f371bc3107e69efce563a3d0f0e6880de0d537 upstream.

The autofs packet size has had a very unfortunate size problem on x86:
because the alignment of 'u64' differs in 32-bit and 64-bit modes, and
because the packet data was not 8-byte aligned, the size of the autofsv5
packet structure differed between 32-bit and 64-bit modes despite
looking otherwise identical (300 vs 304 bytes respectively).

We first fixed that up by making the 64-bit compat mode know about this
problem in commit a32744d4abae ("autofs: work around unhappy compat
problem on x86-64"), and that made a 32-bit 'systemd' work happily on a
64-bit kernel because everything then worked the same way as on a 32-bit

But it turned out that 'automount' had actually known and worked around
this problem in user space, so fixing the kernel to do the proper 32-bit
compatibility handling actually *broke* 32-bit automount on a 64-bit
kernel, because it knew that the packet sizes were wrong and expected
those incorrect sizes.

As a result, we ended up reverting that compatibility mode fix, and
thus breaking systemd again, in commit fcbf94b9dedd.

With both automount and systemd doing a single read() system call, and
verifying that they get *exactly* the size they expect but using
different sizes, it seemed that fixing one of them inevitably seemed to
break the other.  At one point, a patch I seriously considered applying
from Michael Tokarev did a "strcmp()" to see if it was automount that
was doing the operation.  Ugly, ugly.

However, a prettier solution exists now thanks to the packetized pipe
mode.  By marking the communication pipe as being packetized (by simply
setting the O_DIRECT flag), we can always just write the bigger packet
size, and if user-space does a smaller read, it will just get that
partial end result and the extra alignment padding will simply be thrown

This makes both automount and systemd happy, since they now get the size
they asked for, and the kernel side of autofs simply no longer needs to
care - it could pad out the packet arbitrarily.

Of course, if there is some *other* user of autofs (please, please,
please tell me it ain't so - and we haven't heard of any) that tries to
read the packets with multiple writes, that other user will now be
broken - the whole point of the packetized mode is that one system call
gets exactly one packet, and you cannot read a packet in pieces.

Tested-by: Michael Tokarev <>
Cc: Alan Cox <>
Cc: David Miller <>
Cc: Ian Kent <>
Cc: Thomas Meyer <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agopipes: add a "packetized pipe" mode for writing
Linus Torvalds [Sun, 29 Apr 2012 20:12:42 +0000 (13:12 -0700)]
pipes: add a "packetized pipe" mode for writing

commit 9883035ae7edef3ec62ad215611cb8e17d6a1a5d upstream.

The actual internal pipe implementation is already really about
individual packets (called "pipe buffers"), and this simply exposes that
as a special packetized mode.

When we are in the packetized mode (marked by O_DIRECT as suggested by
Alan Cox), a write() on a pipe will not merge the new data with previous
writes, so each write will get a pipe buffer of its own.  The pipe
buffer is then marked with the PIPE_BUF_FLAG_PACKET flag, which in turn
will tell the reader side to break the read at that boundary (and throw
away any partial packet contents that do not fit in the read buffer).

End result: as long as you do writes less than PIPE_BUF in size (so that
the pipe doesn't have to split them up), you can now treat the pipe as a
packet interface, where each read() system call will read one packet at
a time.  You can just use a sufficiently big read buffer (PIPE_BUF is
sufficient, since bigger than that doesn't guarantee atomicity anyway),
and the return value of the read() will naturally give you the size of
the packet.

NOTE! We do not support zero-sized packets, and zero-sized reads and
writes to a pipe continue to be no-ops.  Also note that big packets will
currently be split at write time, but that the size at which that
happens is not really specified (except that it's bigger than PIPE_BUF).
Currently that limit is the system page size, but we might want to
explicitly support bigger packets some day.

The main user for this is going to be the autofs packet interface,
allowing us to stop having to care so deeply about exact packet sizes
(which have had bugs with 32/64-bit compatibility modes).  But user
space can create packetized pipes with "pipe2(fd, O_DIRECT)", which will
fail with an EINVAL on kernels that do not support this interface.

Tested-by: Michael Tokarev <>
Cc: Alan Cox <>
Cc: David Miller <>
Cc: Ian Kent <>
Cc: Thomas Meyer <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agousb gadget: uvc: uvc_request_data::length field must be signed
Laurent Pinchart [Tue, 24 Apr 2012 09:29:42 +0000 (11:29 +0200)]
usb gadget: uvc: uvc_request_data::length field must be signed

commit 6f6543f53f9ce136e01d7114bf6f0818ca54fb41 upstream.

The field is used to pass the UVC request data length, but can also be
used to signal an error when setting it to a negative value. Switch from
unsigned int to __s32.

Reported-by: Fernandez Gonzalo <>
Signed-off-by: Laurent Pinchart <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoUSB: gadget: storage gadgets send wrong error code for unknown commands
Alan Stern [Wed, 11 Apr 2012 20:09:10 +0000 (16:09 -0400)]
USB: gadget: storage gadgets send wrong error code for unknown commands

commit c85dcdac5852295cf6822f5c4331a6ddab72581f upstream.

This patch (as1539) fixes a minor bug in the mass-storage gadget
drivers.  When an unknown command is received, the error code sent
back is "Invalid Field in CDB" rather than "Invalid Command".  This is
because the bitmask of CDB bytes allowed to be nonzero is incorrect.

When handling an unknown command, we don't care which command bytes
are nonzero.  All the bits in the mask should be set, not just eight
of them.

Signed-off-by: Alan Stern <>
CC: Michal Nazarewicz <>
Signed-off-by: Felipe Balbi <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoUSB: EHCI: fix crash during suspend on ASUS computers
Alan Stern [Tue, 24 Apr 2012 18:07:22 +0000 (14:07 -0400)]
USB: EHCI: fix crash during suspend on ASUS computers

commit 151b61284776be2d6f02d48c23c3625678960b97 upstream.

This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers.  Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.

After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state.  Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.

The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep.  Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.

This fixes Bugzilla #42728.

Signed-off-by: Alan Stern <>
Tested-by: Steven Rostedt <>
Tested-by: Andrey Rahmatullin <>
Tested-by: Oleksij Rempel (fishor) <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoUSB: cdc-wdm: fix race leading leading to memory corruption
Oliver Neukum [Thu, 26 Apr 2012 19:59:10 +0000 (21:59 +0200)]
USB: cdc-wdm: fix race leading leading to memory corruption

commit 5c22837adca7c30b66121cf18ad3e160134268d4 upstream.

This patch fixes a race whereby a pointer to a buffer
would be overwritten while the buffer was in use leading
to a double free and a memory leak. This causes crashes.
This bug was introduced in 2.6.34

Signed-off-by: Oliver Neukum <>
Tested-by: Bjørn Mork <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoRevert "usb: Fix build error due to dma_mask is not at pdev_archdata at ARM"
Greg Kroah-Hartman [Mon, 30 Apr 2012 01:09:01 +0000 (18:09 -0700)]
Revert "usb: Fix build error due to dma_mask is not at pdev_archdata at ARM"

This reverts commit d39514c14bd941232976b68e2750dc725b90e724 which is
e90fc3cb087ce5c5f81e814358222cd6d197b5db upstream as it causes oopses on
some ppc systems.

Reported-by: Chen Peter-B29397 <>
Cc: Ramneek Mehresh <>
Cc: Peter Chen <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agonfsd: fix error values returned by nfsd4_lockt() when nfsd_open() fails
Al Viro [Fri, 27 Apr 2012 22:54:38 +0000 (17:54 -0500)]
nfsd: fix error values returned by nfsd4_lockt() when nfsd_open() fails

commit 04da6e9d63427b2d0fd04766712200c250b3278f upstream.

nfsd_open() already returns an NFS error value; only vfs_test_lock()
result needs to be fed through nfserrno().  Broken by commit 55ef12
(nfsd: Ensure nfsv4 calls the underlying filesystem on LOCKT)
three years ago...

Signed-off-by: Al Viro <>
Signed-off-by: Jonathan Nieder <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agonfsd: fix b0rken error value for setattr on read-only mount
Al Viro [Fri, 27 Apr 2012 22:42:43 +0000 (17:42 -0500)]
nfsd: fix b0rken error value for setattr on read-only mount

commit 96f6f98501196d46ce52c2697dd758d9300c63f5 upstream.

..._want_write() returns -EROFS on failure, _not_ an NFS error value.

Signed-off-by: Al Viro <>
Signed-off-by: Jonathan Nieder <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agommc: unbreak sdhci-esdhc-imx on i.MX25
Eric Bénard [Fri, 27 Apr 2012 22:31:18 +0000 (17:31 -0500)]
mmc: unbreak sdhci-esdhc-imx on i.MX25

commit b89152824f993a9572b47eb31f4579feadeac34c upstream.

This was broken by me in 37865fe91582582a6f6c00652f6a2b1ff71f8a78
("mmc: sdhci-esdhc-imx: fix timeout on i.MX's sdhci") where more
extensive tests would have shown that read or write of data to the
card were failing (even if the partition table was correctly read).

Signed-off-by: Eric Bénard <>
Acked-by: Wolfram Sang <>
Signed-off-by: Chris Ball <>
Signed-off-by: Jonathan Nieder <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoKVM: unmap pages from the iommu when slots are removed
Alex Williamson [Fri, 27 Apr 2012 21:54:08 +0000 (16:54 -0500)]
KVM: unmap pages from the iommu when slots are removed

commit 32f6daad4651a748a58a3ab6da0611862175722f upstream.

We've been adding new mappings, but not destroying old mappings.
This can lead to a page leak as pages are pinned using
get_user_pages, but only unpinned with put_page if they still
exist in the memslots list on vm shutdown.  A memslot that is
destroyed while an iommu domain is enabled for the guest will
therefore result in an elevated page reference count that is
never cleared.

Additionally, without this fix, the iommu is only programmed
with the first translation for a gpa.  This can result in
peer-to-peer errors if a mapping is destroyed and replaced by a
new mapping at the same gpa as the iommu will still be pointing
to the original, pinned memory address.

Signed-off-by: Alex Williamson <>
Signed-off-by: Marcelo Tosatti <>
Signed-off-by: Jonathan Nieder <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoFix modpost failures in fedora 17
David Miller [Thu, 26 Apr 2012 00:41:32 +0000 (19:41 -0500)]
Fix modpost failures in fedora 17

commit e88aa7bbbe3046a125ea1936b16bb921cc9c6349 upstream.

The symbol table on x86-64 starts to have entries that have names


They are of type STT_FUNCTION and this one had a length of 18.  This
matched the device ID validation logic and it barfed because the
length did not meet the device type's criteria.

FATAL: arch/x86/crypto/aesni-intel: sizeof(struct x86cpu_device_id)=16 is not a modulo of the size of section __mod_x86cpu_device_table=18.
Fix definition of struct x86cpu_device_id in mod_devicetable.h

These are some kind of compiler tool internal stuff being emitted and
not something we want to inspect in modpost's device ID table
validation code.

So skip the symbol if it is not of type STT_OBJECT.

Signed-off-by: David S. Miller <>
Acked-by: Sam Ravnborg <>
Signed-off-by: Michal Marek <>
Signed-off-by: Jonathan Nieder <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agobrcm80211: smac: resume transmit fifo upon receiving frames
Arend van Spriel [Wed, 25 Apr 2012 22:39:59 +0000 (17:39 -0500)]
brcm80211: smac: resume transmit fifo upon receiving frames

commit badc4f07622f0f7093a201638f45e85765f1b5e4 upstream.

There have been reports about not being able to use access-points
on channel 12 and 13 or having connectivity issues when these channels
were part of the selected regulatory domain. Upon switching to these
channels the brcmsmac driver suspends the transmit dma fifos. This
patch resumes them upon handing over the first received beacon to

This patch is to be applied to the stable tree for kernel versions
3.2 and 3.3.

Tested-by: Francesco Saverio Schiavarelli <>
Reviewed-by: Pieter-Paul Giesberts <>
Reviewed-by: Brett Rudley <>
Signed-off-by: Arend van Spriel <>
Signed-off-by: John W. Linville <>
Signed-off-by: Jonathan Nieder <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoEHCI: fix criterion for resuming the root hub
Alan Stern [Wed, 25 Apr 2012 06:17:42 +0000 (01:17 -0500)]
EHCI: fix criterion for resuming the root hub

commit dc75ce9d929aabeb0843a6b1a4ab320e58ba1597 upstream.

This patch (as1542) changes the criterion ehci-hcd uses to tell when
it needs to resume the controller's root hub.  A resume is needed when
a port status change is detected, obviously, but only if the root hub
is currently suspended.

Right now the driver tests whether the root hub is running, and that
is not the correct test.  In particular, if the controller has died
then the root hub should not be restarted.  In addition, some buggy
hardware occasionally requires the root hub to be running and
sending out SOF packets even while it is nominally supposed to be

In the end, the test needs to be changed.  Rather than checking whether
the root hub is currently running, the driver will now check whether
the root hub is currently suspended.  This will yield the correct
behavior in all cases.

Signed-off-by: Alan Stern <>
CC: Peter Chen <>
Signed-off-by: Greg Kroah-Hartman <>
Signed-off-by: Jonathan Nieder <>
5 years agonl80211: ensure interface is up in various APIs
Johannes Berg [Mon, 2 Apr 2012 08:51:55 +0000 (10:51 +0200)]
nl80211: ensure interface is up in various APIs

commit 2b5f8b0b44e17e625cfba1e7b88db44f4dcc0441 upstream.
[backported by Ben Greear]

The nl80211 handling code should ensure as much as
it can that the interface is in a valid state, it
can certainly ensure the interface is running.

Not doing so can cause calls through mac80211 into
the driver that result in warnings and unspecified
behaviour in the driver.

Reported-by: Ben Greear <>
Signed-off-by: Johannes Berg <>
Signed-off-by: John W. Linville <>
Signed-off-by: Ben Greear <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agodrm/i915: fix integer overflow in i915_gem_do_execbuffer()
Xi Wang [Mon, 23 Apr 2012 08:06:42 +0000 (04:06 -0400)]
drm/i915: fix integer overflow in i915_gem_do_execbuffer()

commit 44afb3a04391a74309d16180d1e4f8386fdfa745 upstream.

On 32-bit systems, a large args->num_cliprects from userspace via ioctl
may overflow the allocation size, leading to out-of-bounds access.

This vulnerability was introduced in commit 432e58ed ("drm/i915: Avoid
allocation for execbuffer object list").

Signed-off-by: Xi Wang <>
Reviewed-by: Chris Wilson <>
Signed-off-by: Daniel Vetter <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agodrm/i915: fix integer overflow in i915_gem_execbuffer2()
Xi Wang [Mon, 23 Apr 2012 08:06:41 +0000 (04:06 -0400)]
drm/i915: fix integer overflow in i915_gem_execbuffer2()

commit ed8cd3b2cd61004cab85380c52b1817aca1ca49b upstream.

On 32-bit systems, a large args->buffer_count from userspace via ioctl
may overflow the allocation size, leading to out-of-bounds access.

This vulnerability was introduced in commit 8408c282 ("drm/i915:
First try a normal large kmalloc for the temporary exec buffers").

Signed-off-by: Xi Wang <>
Reviewed-by: Chris Wilson <>
Signed-off-by: Daniel Vetter <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agodrm/i915: handle input/output sdvo timings separately in mode_set
Daniel Vetter [Sun, 1 Apr 2012 17:16:18 +0000 (19:16 +0200)]
drm/i915: handle input/output sdvo timings separately in mode_set

commit 6651819b4b4fc3caa6964c5d825eb4bb996f3905 upstream.

We seem to have a decent confusion between the output timings and the
input timings of the sdvo encoder. If I understand the code correctly,
we use the original mode unchanged for the output timings, safe for
the lvds case. And we should use the adjusted mode for input timings.

Clarify the situation by adding an explicit output_dtd to the sdvo
mode_set function and streamline the code-flow by moving the input and
output mode setting in the sdvo encode together.

Furthermore testing showed that the sdvo input timing needs the
unadjusted dotclock, the sdvo chip will automatically compute the
required pixel multiplier to get a dotclock above 100 MHz.

Fix this up when converting a drm mode to an sdvo dtd.

This regression was introduced in

commit c74696b9c890074c1e1ee3d7496fc71eb3680ced
Author: Pavel Roskin <>
Date:   Thu Sep 2 14:46:34 2010 -0400

    i915: revert some checks added by commit 32aad86f

particularly the following hunk:

# diff --git a/drivers/gpu/drm/i915/intel_sdvo.c
# b/drivers/gpu/drm/i915/intel_sdvo.c
# index 093e914..62d22ae 100644
# --- a/drivers/gpu/drm/i915/intel_sdvo.c
# +++ b/drivers/gpu/drm/i915/intel_sdvo.c
# @@ -1122,11 +1123,9 @@ static void intel_sdvo_mode_set(struct drm_encoder *encoder,
#      /* We have tried to get input timing in mode_fixup, and filled into
# adjusted_mode */
# -    if (intel_sdvo->is_tv || intel_sdvo->is_lvds) {
# -        intel_sdvo_get_dtd_from_mode(&input_dtd, adjusted_mode);
# +    intel_sdvo_get_dtd_from_mode(&input_dtd, adjusted_mode);
# +    if (intel_sdvo->is_tv || intel_sdvo->is_lvds)
#  input_dtd.part2.sdvo_flags = intel_sdvo->sdvo_flags;
# -    } else
# -        intel_sdvo_get_dtd_from_mode(&input_dtd, mode);
#      /* If it's a TV, we already set the output timing in mode_fixup.
#       * Otherwise, the output timing is equal to the input timing.

Due to questions raised in review, below a more elaborate analysis of
the bug at hand:

Sdvo seems to have two timings, one is the output timing which will be
sent over whatever is connected on the other side of the sdvo chip (panel,
hdmi screen, tv), the other is the input timing which will be generated by
the gmch pipe. It looks like sdvo is expected to scale between the two.

To make things slightly more complicated, we have a bunch of special
- For lvds panel we always use a fixed output timing, namely
  intel_sdvo->sdvo_lvds_fixed_mode, hence that special case.
- Sdvo has an interface to generate a preferred input timing for a given
  output timing. This is the confusing thing that I've tried to clear up
  with the follow-on patches.
- A special requirement is that the input pixel clock needs to be between
  100MHz and 200MHz (likely to keep it within the electromechanical design
  range of PCIe), 270MHz on later gen4+. Lower pixel clocks are

The thing this patch tries to fix is that the pipe needs to be
explicitly instructed to double/quadruple the pixels and needs the
correspondingly higher pixel clock, whereas the sdvo adaptor seems to
do that itself and needs the unadjusted pixel clock. For the sdvo
encode side we already set the pixel mutliplier with a different
command (0x21).

This patch tries to fix this mess by:
- Keeping the output mode timing in the unadjusted plain mode, safe
  for the lvds case.
- Storing the input timing in the adjusted_mode with the adjusted
  pixel clock. This way we don't need to frob around with the core
  crtc mode set code.
- Fixing up the pixelclock when constructing the sdvo dtd timing
  struct. This is why the first hunk of the patch is an integral part
  of the series.
- Dropping the is_tv special case because input_dtd is equivalent to
  adjusted_mode after these changes. Follow-up patches clear this up
  further (by simply ripping out intel_sdvo->input_dtd because it's
  not needed).

v2: Extend commit message with an in-depth bug analysis.

Reported-and-Tested-by: Bernard Blackham <>
Reviewed-by: Jesse Barnes <>
Signed-off-by: Daniel Vetter <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agohwmon: (fam15h_power) Fix pci_device_id array
Guenter Roeck [Wed, 25 Apr 2012 20:44:20 +0000 (13:44 -0700)]
hwmon: (fam15h_power) Fix pci_device_id array

commit c3e40a9972428d6e2d8e287ed0233a57a218c30f upstream.

pci_match_id() takes an *array* of IDs which must be properly zero-

Reported-by: Ben Hutchings <>
Signed-off-by: Guenter Roeck <>
Acked-by: Jean Delvare <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agohwmon: fam15h_power: fix bogus values with current BIOSes
Andre Przywara [Mon, 9 Apr 2012 22:16:34 +0000 (18:16 -0400)]
hwmon: fam15h_power: fix bogus values with current BIOSes

commit 00250ec90963b7ef6678438888f3244985ecde14 upstream.

Newer BKDG[1] versions recommend a different initialization value for
the running average range register in the northbridge. This improves
the power reading by avoiding counter saturations resulting in bogus
values for anything below about 80% of TDP power consumption.
Updated BIOSes will have this new value set up from the beginning,
but meanwhile we correct this value ourselves.
This needs to be done on all northbridges, even on those where the
driver itself does not register at.

This fixes the driver on all current machines to provide proper
values for idle load.

Chapter 3.8: D18F5xE0 Processor TDP Running Average (p. 452)

Signed-off-by: Andre Przywara <>
Acked-by: Jean Delvare <>
[ Removed unnecessary return statement]
Signed-off-by: Guenter Roeck <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agodmaengine: at_hdmac: remove clear-on-read in atc_dostart()
Nicolas Ferre [Mon, 16 Apr 2012 12:46:30 +0000 (14:46 +0200)]
dmaengine: at_hdmac: remove clear-on-read in atc_dostart()

commit ed8b0d67f33518a16c6b2450fe5ebebf180c2d04 upstream.

This loop on EBCISR register was designed to clear IRQ sources before enabling
a DMA channel. This register is clear-on-read so a race condition can appear if
another channel is already active and has just finished its transfer.
Removing this read on EBCISR is fixing the issue as there is no case where an IRQ
could be pending: we already make sure that this register is drained at probe()
time and during resume.

Signed-off-by: Nicolas Ferre <>
Signed-off-by: Vinod Koul <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoASoC: dapm: Ensure power gets managed for line widgets
Mark Brown [Thu, 12 Apr 2012 16:29:36 +0000 (17:29 +0100)]
ASoC: dapm: Ensure power gets managed for line widgets

commit 7e1f7c8a6e517900cd84da1b8ae020f08f286c3b upstream.

Line widgets had not been included in either the power up or power down
sequences so if a widget had an event associated with it that event would
never be run. Fix this minimally by adding them to the sequences, we
should probably be doing away with the specific widget types as they all
have the same priority anyway.

Signed-off-by: Mark Brown <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoxen/smp: Fix crash when booting with ACPI hotplug CPUs.
Konrad Rzeszutek Wilk [Thu, 26 Apr 2012 17:50:03 +0000 (13:50 -0400)]
xen/smp: Fix crash when booting with ACPI hotplug CPUs.

commit cf405ae612b0f7e2358db7ff594c0e94846137aa upstream.

When we boot on a machine that can hotplug CPUs and we
are using 'dom0_max_vcpus=X' on the Xen hypervisor line
to clip the amount of CPUs available to the initial domain,
we get this:

(XEN) Command line: com1=115200,8n1 dom0_mem=8G noreboot dom0_max_vcpus=8 sync_console mce_verbosity=verbose console=com1,vga loglvl=all guest_loglvl=all
.. snip..
DMI: Intel Corporation S2600CP/S2600CP, BIOS SE5C600.86B.99.99.x032.072520111118 07/25/2011
.. snip.
SMP: Allowing 64 CPUs, 32 hotplug CPUs
installing Xen timer for CPU 7
cpu 7 spinlock event irq 361
NMI watchdog: disabled (cpu7): hardware events not enabled
Brought up 8 CPUs
.. snip..
[acpi processor finds the CPUs are not initialized and starts calling
arch_register_cpu, which creates /sys/devices/system/cpu/cpu8/online]
CPU 8 got hotplugged
CPU 9 got hotplugged
CPU 10 got hotplugged
.. snip..
initcall 1_acpi_battery_init_async+0x0/0x1b returned 0 after 406 usecs
calling  erst_init+0x0/0x2bb @ 1

[and the scheduler sticks newly started tasks on the new CPUs, but
said CPUs cannot be initialized b/c the hypervisor has limited the
amount of vCPUS to 8 - as per the dom0_max_vcpus=8 flag.
The spinlock tries to kick the other CPU, but the structure for that
is not initialized and we crash.]
BUG: unable to handle kernel paging request at fffffffffffffed8
IP: [<ffffffff81035289>] xen_spin_lock+0x29/0x60
PGD 180d067 PUD 180e067 PMD 0
Oops: 0002 [#1] SMP
Modules linked in:

Pid: 1, comm: swapper/0 Not tainted 3.4.0-rc2upstream-00001-gf5154e8 #1 Intel Corporation S2600CP/S2600CP
RIP: e030:[<ffffffff81035289>]  [<ffffffff81035289>] xen_spin_lock+0x29/0x60
RSP: e02b:ffff8801fb9b3a70  EFLAGS: 00010282

With this patch, we cap the amount of vCPUS that the initial domain
can run, to exactly what dom0_max_vcpus=X has specified.

In the future, if there is a hypercall that will allow a running
domain to expand past its initial set of vCPUS, this patch should
be re-evaluated.

Signed-off-by: Konrad Rzeszutek Wilk <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoxen: correctly check for pending events when restoring irq flags
David Vrabel [Thu, 26 Apr 2012 18:44:06 +0000 (19:44 +0100)]
xen: correctly check for pending events when restoring irq flags

commit 7eb7ce4d2e8991aff4ecb71a81949a907ca755ac upstream.

In xen_restore_fl_direct(), xen_force_evtchn_callback() was being
called even if no events were pending.  This resulted in (depending on
workload) about a 100 times as many xen_version hypercalls as

Fix this by correcting the sense of the conditional jump.

This seems to give a significant performance benefit for some

There is some subtle tricksy "..since the check here is trying to
check both pending and masked in a single cmpw, but I think this is
correct. It will call check_events now only when the combined
mask+pending word is 0x0001 (aka unmasked, pending)." (Ian)

Acked-by: Ian Campbell <>
Signed-off-by: David Vrabel <>
Signed-off-by: Konrad Rzeszutek Wilk <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoRevert "autofs: work around unhappy compat problem on x86-64"
Linus Torvalds [Sat, 28 Apr 2012 15:29:56 +0000 (08:29 -0700)]
Revert "autofs: work around unhappy compat problem on x86-64"

commit fcbf94b9dedd2ce08e798a99aafc94fec8668161 upstream.

This reverts commit a32744d4abae24572eff7269bc17895c41bd0085.

While that commit was technically the right thing to do, and made the
x86-64 compat mode work identically to native 32-bit mode (and thus
fixing the problem with a 32-bit systemd install on a 64-bit kernel), it
turns out that the automount binaries had workarounds for this compat

Now, the workarounds are disgusting: doing an "uname()" to find out the
architecture of the kernel, and then comparing it for the 64-bit cases
and fixing up the size of the read() in automount for those.  And they
were confused: it's not actually a generic 64-bit issue at all, it's
very much tied to just x86-64, which has different alignment for an
'u64' in 64-bit mode than in 32-bit mode.

But the end result is that fixing the compat layer actually breaks the
case of a 32-bit automount on a x86-64 kernel.

There are various approaches to fix this (including just doing a
"strcmp()" on current->comm and comparing it to "automount"), but I
think that I will do the one that teaches pipes about a special "packet
mode", which will allow user space to not have to care too deeply about
the padding at the end of the autofs packet.

That change will make the compat workaround unnecessary, so let's revert
it first, and get automount working again in compat mode.  The
packetized pipes will then fix autofs for systemd.

Reported-and-requested-by: Michael Tokarev <>
Cc: Ian Kent <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agox86, apic: APIC code touches invalid MSR on P5 class machines
Bryan O'Donoghue [Wed, 18 Apr 2012 16:37:39 +0000 (17:37 +0100)]
x86, apic: APIC code touches invalid MSR on P5 class machines

commit cbf2829b61c136edcba302a5e1b6b40e97d32c00 upstream.

Current APIC code assumes MSR_IA32_APICBASE is present for all systems.
Pentium Classic P5 and friends didn't have this MSR. MSR_IA32_APICBASE
was introduced as an architectural MSR by Intel @ P6.

Code paths that can touch this MSR invalidly are when vendor == Intel &&
cpu-family == 5 and APIC bit is set in CPUID - or when you simply pass
lapic on the kernel command line, on a P5.

The below patch stops Linux incorrectly interfering with the
MSR_IA32_APICBASE for P5 class machines. Other code paths exist that
touch the MSR - however those paths are not currently reachable for a
conformant P5.

Signed-off-by: Bryan O'Donoghue <>
Signed-off-by: H. Peter Anvin <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoNFSv4: Ensure that we check lock exclusive/shared type against open modes
Trond Myklebust [Wed, 18 Apr 2012 16:48:35 +0000 (12:48 -0400)]
NFSv4: Ensure that we check lock exclusive/shared type against open modes

commit 55725513b5ef9d462aa3e18527658a0362aaae83 upstream.

Since we may be simulating flock() locks using NFS byte range locks,
we can't rely on the VFS having checked the file open mode for us.

Signed-off-by: Trond Myklebust <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoNFSv4: Ensure that the LOCK code sets exception->inode
Trond Myklebust [Wed, 18 Apr 2012 16:20:10 +0000 (12:20 -0400)]
NFSv4: Ensure that the LOCK code sets exception->inode

commit 05ffe24f5290dc095f98fbaf84afe51ef404ccc5 upstream.

All callers of nfs4_handle_exception() that need to handle
NFS4ERR_OPENMODE correctly should set exception->inode

Signed-off-by: Trond Myklebust <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agonfs: Enclose hostname in brackets when needed in nfs_do_root_mount
Jan Kara [Fri, 2 Sep 2011 23:09:43 +0000 (01:09 +0200)]
nfs: Enclose hostname in brackets when needed in nfs_do_root_mount

commit 98a2139f4f4d7b5fcc3a54c7fddbe88612abed20 upstream.

When hostname contains colon (e.g. when it is an IPv6 address) it needs
to be enclosed in brackets to make parsing of NFS device string possible.
Fix nfs_do_root_mount() to enclose hostname properly when needed. NFS code
actually does not need this as it does not parse the string passed by
nfs_do_root_mount() but the device string is exposed to userspace in

CC: Josh Boyer <>
CC: Trond Myklebust <>
Signed-off-by: Jan Kara <>
Signed-off-by: Trond Myklebust <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoLinux 3.0.30
Greg Kroah-Hartman [Fri, 27 Apr 2012 16:52:09 +0000 (09:52 -0700)]
Linux 3.0.30

5 years agotcp: fix TCP_MAXSEG for established IPv6 passive sockets
Neal Cardwell [Sun, 22 Apr 2012 09:45:47 +0000 (09:45 +0000)]
tcp: fix TCP_MAXSEG for established IPv6 passive sockets

[ Upstream commit d135c522f1234f62e81be29cebdf59e9955139ad ]

Commit f5fff5d forgot to fix TCP_MAXSEG behavior IPv6 sockets, so IPv6
TCP server sockets that used TCP_MAXSEG would find that the advmss of
child sockets would be incorrect. This commit mirrors the advmss logic
from tcp_v4_syn_recv_sock in tcp_v6_syn_recv_sock. Eventually this
logic should probably be shared between IPv4 and IPv6, but this at
least fixes this issue.

Signed-off-by: Neal Cardwell <>
Acked-by: Eric Dumazet <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agonet ax25: Reorder ax25_exit to remove races.
Eric W. Biederman [Wed, 18 Apr 2012 16:11:23 +0000 (16:11 +0000)]
net ax25: Reorder ax25_exit to remove races.

[ Upstream commit 3adadc08cc1e2cbcc15a640d639297ef5fcb17f5 ]

While reviewing the sysctl code in ax25 I spotted races in ax25_exit
where it is possible to receive notifications and packets after already
freeing up some of the data structures needed to process those
notifications and updates.

Call unregister_netdevice_notifier early so that the rest of the cleanup
code does not need to deal with network devices.  This takes advantage
of my recent enhancement to unregister_netdevice_notifier to send
unregister notifications of all network devices that are current

Move the unregistration for packet types, socket types and protocol
types before we cleanup any of the ax25 data structures to remove the
possibilities of other races.

Signed-off-by: Eric W. Biederman <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoksz884x: don't copy too much in netdev_set_mac_address()
Dan Carpenter [Thu, 19 Apr 2012 07:00:19 +0000 (10:00 +0300)]
ksz884x: don't copy too much in netdev_set_mac_address()

[ Upstream commit 716af4abd6e6370226f567af50bfaca274515980 ]

MAX_ADDR_LEN is 32.  ETH_ALEN is 6.  mac->sa_data is a 14 byte array, so
the memcpy() is doing a read past the end of the array.  I asked about
this on netdev and Ben Hutchings told me it's supposed to be copying
ETH_ALEN bytes (thanks Ben).

Signed-off-by: Dan Carpenter <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agonetns: do not leak net_generic data on failed init
Julian Anastasov [Mon, 16 Apr 2012 04:43:15 +0000 (04:43 +0000)]
netns: do not leak net_generic data on failed init

[ Upstream commit b922934d017f1cc831b017913ed7d1a56c558b43 ]

ops_init should free the net_generic data on
init failure and __register_pernet_operations should not
call ops_free when NET_NS is not enabled.

Signed-off-by: Julian Anastasov <>
Reviewed-by: "Eric W. Biederman" <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agotcp: fix tcp_grow_window() for large incoming frames
Eric Dumazet [Mon, 16 Apr 2012 23:28:07 +0000 (23:28 +0000)]
tcp: fix tcp_grow_window() for large incoming frames

[ Upstream commit 4d846f02392a710f9604892ac3329e628e60a230 ]

tcp_grow_window() has to grow rcv_ssthresh up to window_clamp, allowing
sender to increase its window.

tcp_grow_window() still assumes a tcp frame is under MSS, but its no
longer true with LRO/GRO.

This patch fixes one of the performance issue we noticed with GRO on.

Signed-off-by: Eric Dumazet <>
Cc: Neal Cardwell <>
Cc: Tom Herbert <>
Acked-by: Neal Cardwell <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agodummy: Add ndo_uninit().
Hiroaki SHIMODA [Sun, 15 Apr 2012 13:26:01 +0000 (13:26 +0000)]
dummy: Add ndo_uninit().

[ Upstream commit 890fdf2a0cb88202d1427589db2cf29c1bdd3c1d ]

In register_netdevice(), when ndo_init() is successful and later
some error occurred, ndo_uninit() will be called.
So dummy deivce is desirable to implement ndo_uninit() method
to free percpu stats for this case.
And, ndo_uninit() is also called along with dev->destructor() when
device is unregistered, so in order to prevent dev->dstats from
being freed twice, dev->destructor is modified to free_netdev().

Signed-off-by: Hiroaki SHIMODA <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agonet: usb: smsc75xx: fix mtu
Stephane Fillod [Sun, 15 Apr 2012 11:38:29 +0000 (11:38 +0000)]
net: usb: smsc75xx: fix mtu

[ Upstream commit a99ff7d0123b19ecad3b589480b6542716ab6b52 ]

Make smsc75xx recalculate the hard_mtu after adjusting the

Without this, usbnet adjusts the MTU down to 1492 bytes, and the host is
unable to receive standard 1500-byte frames from the device.

Inspired by same fix on cdc_eem 78fb72f7936c01d5b426c03a691eca082b03f2b9.

Tested on ARM/Omap3 with EVB-LAN7500-LC.

Signed-off-by: Stephane Fillod <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agonet_sched: gred: Fix oops in gred_dump() in WRED mode
David Ward [Sun, 15 Apr 2012 12:31:45 +0000 (12:31 +0000)]
net_sched: gred: Fix oops in gred_dump() in WRED mode

[ Upstream commit 244b65dbfede788f2fa3fe2463c44d0809e97c6b ]

A parameter set exists for WRED mode, called wred_set, to hold the same
values for qavg and qidlestart across all VQs. The WRED mode values had
been previously held in the VQ for the default DP. After these values
were moved to wred_set, the VQ for the default DP was no longer created
automatically (so that it could be omitted on purpose, to have packets
in the default DP enqueued directly to the device without using RED).

However, gred_dump() was overlooked during that change; in WRED mode it
still reads qavg/qidlestart from the VQ for the default DP, which might
not even exist. As a result, this command sequence will cause an oops:

tc qdisc add dev $DEV handle $HANDLE parent $PARENT gred setup \
    DPs 3 default 2 grio
tc qdisc change dev $DEV handle $HANDLE gred DP 0 prio 8 $RED_OPTIONS
tc qdisc change dev $DEV handle $HANDLE gred DP 1 prio 8 $RED_OPTIONS

This fixes gred_dump() in WRED mode to use the values held in wred_set.

Signed-off-by: David Ward <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agonet/ethernet: ks8851_mll fix rx frame buffer overflow
Davide Ciminaghi [Fri, 13 Apr 2012 04:48:25 +0000 (04:48 +0000)]
net/ethernet: ks8851_mll fix rx frame buffer overflow

[ Upstream commit 8a9a0ea6032186e3030419262678d652b88bf6a8 ]

At the beginning of ks_rcv(), a for loop retrieves the
header information relevant to all the frames stored
in the mac's internal buffers. The number of pending
frames is stored as an 8 bits field in KS_RXFCTR.
If interrupts are disabled long enough to allow for more than
32 frames to accumulate in the MAC's internal buffers, a buffer
overflow occurs.
This patch fixes the problem by making the
driver's frame_head_info buffer big enough.
Well actually, since the chip appears to have 12K of
internal rx buffers and the shortest ethernet frame should
be 64 bytes long, maybe the limit could be set to
12*1024/64 = 192 frames, but 255 should be safer.

Signed-off-by: Davide Ciminaghi <>
Signed-off-by: Raffaele Recalcati <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agonet: smsc911x: fix skb handling in receive path
Will Deacon [Thu, 12 Apr 2012 05:54:09 +0000 (05:54 +0000)]
net: smsc911x: fix skb handling in receive path

[ Upstream commit 3c5e979bd037888dd7d722da22da4b43659af485 ]

The SMSC911x driver resets the ->head, ->data and ->tail pointers in the
skb on the reset path in order to avoid buffer overflow due to packet
padding performed by the hardware.

This patch fixes the receive path so that the skb pointers are fixed up
after the data has been read from the device, The error path is also
fixed to use number of words consistently and prevent erroneous FIFO
fastforwarding when skipping over bad data.

Signed-off-by: Will Deacon <>
Signed-off-by: Eric Dumazet <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years ago8139cp: set intr mask after its handler is registered
Jason Wang [Wed, 11 Apr 2012 22:10:54 +0000 (22:10 +0000)]
8139cp: set intr mask after its handler is registered

[ Upstream commit a8c9cb106fe79c28d6b7f1397652cadd228715ff ]

We set intr mask before its handler is registered, this does not work well when
8139cp is sharing irq line with other devices. As the irq could be enabled by
the device before 8139cp's hander is registered which may lead unhandled
irq. Fix this by introducing an helper cp_irq_enable() and call it after

Signed-off-by: Jason Wang <>
Reviewed-by: Flavio Leitner <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoatl1: fix kernel panic in case of DMA errors
Tony Zelenoff [Wed, 11 Apr 2012 06:15:03 +0000 (06:15 +0000)]
atl1: fix kernel panic in case of DMA errors

[ Upstream commit 03662e41c7cff64a776bfb1b3816de4be43de881 ]

There was two separate work_struct structures which share one
handler. Unfortunately getting atl1_adapter structure from
work_struct in case of DMA error was done from incorrect
offset which cause kernel panics.

The useless work_struct for DMA error removed and
handler name changed to more generic one.

Signed-off-by: Tony Zelenoff <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agotcp: fix tcp_rcv_rtt_update() use of an unscaled RTT sample
Neal Cardwell [Tue, 10 Apr 2012 07:59:20 +0000 (07:59 +0000)]
tcp: fix tcp_rcv_rtt_update() use of an unscaled RTT sample

[ Upstream commit 18a223e0b9ec8979320ba364b47c9772391d6d05 ]

Fix a code path in tcp_rcv_rtt_update() that was comparing scaled and
unscaled RTT samples.

The intent in the code was to only use the 'm' measurement if it was a
new minimum.  However, since 'm' had not yet been shifted left 3 bits
but 'new_sample' had, this comparison would nearly always succeed,
leading us to erroneously set our receive-side RTT estimate to the 'm'
sample when that sample could be nearly 8x too high to use.

The overall effect is to often cause the receive-side RTT estimate to
be significantly too large (up to 40% too large for brief periods in
my tests).

Signed-off-by: Neal Cardwell <>
Acked-by: Eric Dumazet <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agonet: fix a race in sock_queue_err_skb()
Eric Dumazet [Fri, 6 Apr 2012 08:49:10 +0000 (10:49 +0200)]
net: fix a race in sock_queue_err_skb()

[ Upstream commit 110c43304db6f06490961529536c362d9ac5732f ]

As soon as an skb is queued into socket error queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.

Signed-off-by: Eric Dumazet <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agonetlink: fix races after skb queueing
Eric Dumazet [Thu, 5 Apr 2012 22:17:46 +0000 (22:17 +0000)]
netlink: fix races after skb queueing

[ Upstream commit 4a7e7c2ad540e54c75489a70137bf0ec15d3a127 ]

As soon as an skb is queued into socket receive_queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.

Signed-off-by: Eric Dumazet <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agowimax: i2400m - prevent a possible kernel bug due to missing fw_name string
Phil Sutter [Mon, 26 Mar 2012 09:01:30 +0000 (09:01 +0000)]
wimax: i2400m - prevent a possible kernel bug due to missing fw_name string

[ Upstream commit 4eee6a3a04e8bb53fbe7de0f64d0524d3fbe3f80 ]

This happened on a machine with a custom hotplug script calling nameif,
probably due to slow firmware loading. At the time nameif uses ethtool
to gather interface information, i2400m->fw_name is zero and so a null
pointer dereference occurs from within i2400m_get_drvinfo().

Signed-off-by: Phil Sutter <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agobonding: properly unset current_arp_slave on slave link up
Veaceslav Falico [Thu, 5 Apr 2012 03:47:43 +0000 (03:47 +0000)]
bonding: properly unset current_arp_slave on slave link up

[ Upstream commit 5a4309746cd74734daa964acb02690c22b3c8911 ]

When a slave comes up, we're unsetting the current_arp_slave without
removing active flags from it, which can lead to situations where we have
more than one slave with active flags in active-backup mode.

To avoid this situation we must remove the active flags from a slave before
removing it as a current_arp_slave.

Signed-off-by: Veaceslav Falico <>
Signed-off-by: Jay Vosburgh <>
Signed-off-by: Andy Gospodarek <>
Signed-off-by: Marcelo Ricardo Leitner <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agophonet: Check input from user before allocating
Sasha Levin [Thu, 5 Apr 2012 12:07:45 +0000 (12:07 +0000)]
phonet: Check input from user before allocating

[ Upstream commit bcf1b70ac6eb0ed8286c66e6bf37cb747cbaa04c ]

A phonet packet is limited to USHRT_MAX bytes, this is never checked during
tx which means that the user can specify any size he wishes, and the kernel
will attempt to allocate that size.

In the good case, it'll lead to the following warning, but it may also cause
the kernel to kick in the OOM and kill a random task on the server.

[ 8921.744094] WARNING: at mm/page_alloc.c:2255 __alloc_pages_slowpath+0x65/0x730()
[ 8921.749770] Pid: 5081, comm: trinity Tainted: G        W    3.4.0-rc1-next-20120402-sasha #46
[ 8921.756672] Call Trace:
[ 8921.758185]  [<ffffffff810b2ba7>] warn_slowpath_common+0x87/0xb0
[ 8921.762868]  [<ffffffff810b2be5>] warn_slowpath_null+0x15/0x20
[ 8921.765399]  [<ffffffff8117eae5>] __alloc_pages_slowpath+0x65/0x730
[ 8921.769226]  [<ffffffff81179c8a>] ? zone_watermark_ok+0x1a/0x20
[ 8921.771686]  [<ffffffff8117d045>] ? get_page_from_freelist+0x625/0x660
[ 8921.773919]  [<ffffffff8117f3a8>] __alloc_pages_nodemask+0x1f8/0x240
[ 8921.776248]  [<ffffffff811c03e0>] kmalloc_large_node+0x70/0xc0
[ 8921.778294]  [<ffffffff811c4bd4>] __kmalloc_node_track_caller+0x34/0x1c0
[ 8921.780847]  [<ffffffff821b0e3c>] ? sock_alloc_send_pskb+0xbc/0x260
[ 8921.783179]  [<ffffffff821b3c65>] __alloc_skb+0x75/0x170
[ 8921.784971]  [<ffffffff821b0e3c>] sock_alloc_send_pskb+0xbc/0x260
[ 8921.787111]  [<ffffffff821b002e>] ? release_sock+0x7e/0x90
[ 8921.788973]  [<ffffffff821b0ff0>] sock_alloc_send_skb+0x10/0x20
[ 8921.791052]  [<ffffffff824cfc20>] pep_sendmsg+0x60/0x380
[ 8921.792931]  [<ffffffff824cb4a6>] ? pn_socket_bind+0x156/0x180
[ 8921.794917]  [<ffffffff824cb50f>] ? pn_socket_autobind+0x3f/0x90
[ 8921.797053]  [<ffffffff824cb63f>] pn_socket_sendmsg+0x4f/0x70
[ 8921.798992]  [<ffffffff821ab8e7>] sock_aio_write+0x187/0x1b0
[ 8921.801395]  [<ffffffff810e325e>] ? sub_preempt_count+0xae/0xf0
[ 8921.803501]  [<ffffffff8111842c>] ? __lock_acquire+0x42c/0x4b0
[ 8921.805505]  [<ffffffff821ab760>] ? __sock_recv_ts_and_drops+0x140/0x140
[ 8921.807860]  [<ffffffff811e07cc>] do_sync_readv_writev+0xbc/0x110
[ 8921.809986]  [<ffffffff811958e7>] ? might_fault+0x97/0xa0
[ 8921.811998]  [<ffffffff817bd99e>] ? security_file_permission+0x1e/0x90
[ 8921.814595]  [<ffffffff811e17e2>] do_readv_writev+0xe2/0x1e0
[ 8921.816702]  [<ffffffff810b8dac>] ? do_setitimer+0x1ac/0x200
[ 8921.818819]  [<ffffffff810e2ec1>] ? get_parent_ip+0x11/0x50
[ 8921.820863]  [<ffffffff810e325e>] ? sub_preempt_count+0xae/0xf0
[ 8921.823318]  [<ffffffff811e1926>] vfs_writev+0x46/0x60
[ 8921.825219]  [<ffffffff811e1a3f>] sys_writev+0x4f/0xb0
[ 8921.827127]  [<ffffffff82658039>] system_call_fastpath+0x16/0x1b
[ 8921.829384] ---[ end trace dffe390f30db9eb7 ]---

Signed-off-by: Sasha Levin <>
Acked-by: Rémi Denis-Courmont <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoipv6: fix array index in ip6_mc_add_src()
RongQing.Li [Wed, 4 Apr 2012 16:47:04 +0000 (16:47 +0000)]
ipv6: fix array index in ip6_mc_add_src()

[ Upstream commit 78d50217baf36093ab320f95bae0d6452daec85c ]

Convert array index from the loop bound to the loop index.

And remove the void type conversion to ip6_mc_del1_src() return
code, seem it is unnecessary, since ip6_mc_del1_src() does not
use __must_check similar attribute, no compiler will report the
warning when it is removed.

v2: enrich the commit header

Signed-off-by: RongQing.Li <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agobridge: Do not send queries on multicast group leaves
Herbert Xu [Wed, 4 Apr 2012 01:01:20 +0000 (01:01 +0000)]
bridge: Do not send queries on multicast group leaves

[ Upstream commit 996304bbea3d2a094b7ba54c3bd65d3fffeac57b ]

As it stands the bridge IGMP snooping system will respond to
group leave messages with queries for remaining membership.
This is both unnecessary and undesirable.  First of all any
multicast routers present should be doing this rather than us.
What's more the queries that we send may end up upsetting other
multicast snooping swithces in the system that are buggy.

In fact, we can simply remove the code that send these queries
because the existing membership expiry mechanism doesn't rely
on them anyway.

So this patch simply removes all code associated with group
queries in response to group leave messages.

Signed-off-by: Herbert Xu <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agosctp: Allow struct sctp_event_subscribe to grow without breaking binaries
Thomas Graf [Tue, 3 Apr 2012 22:17:53 +0000 (22:17 +0000)]
sctp: Allow struct sctp_event_subscribe to grow without breaking binaries

[ Upstream commit acdd5985364f8dc511a0762fab2e683f29d9d692 ]

getsockopt(..., SCTP_EVENTS, ...) performs a length check and returns
an error if the user provides less bytes than the size of struct

Struct sctp_event_subscribe needs to be extended by an u8 for every
new event or notification type that is added.

This obviously makes getsockopt fail for binaries that are compiled
against an older versions of <net/sctp/user.h> which do not contain
all event types.

This patch changes getsockopt behaviour to no longer return an error
if not enough bytes are being provided by the user. Instead, it
returns as much of sctp_event_subscribe as fits into the provided buffer.

This leads to the new behavior that users see what they have been aware
of at compile time.

The setsockopt(..., SCTP_EVENTS, ...) API is already behaving like this.

Signed-off-by: Thomas Graf <>
Acked-by: Vlad Yasevich <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agotcp: allow splice() to build full TSO packets
Eric Dumazet [Wed, 25 Apr 2012 02:12:06 +0000 (22:12 -0400)]
tcp: allow splice() to build full TSO packets

[ This combines upstream commit
  2f53384424251c06038ae612e56231b96ab610ee and the follow-on bug fix
  commit 35f9c09fe9c72eb8ca2b8e89a593e1c151f28fc2 ]

vmsplice()/splice(pipe, socket) call do_tcp_sendpages() one page at a
time, adding at most 4096 bytes to an skb. (assuming PAGE_SIZE=4096)

The call to tcp_push() at the end of do_tcp_sendpages() forces an
immediate xmit when pipe is not already filled, and tso_fragment() try
to split these skb to MSS multiples.

4096 bytes are usually split in a skb with 2 MSS, and a remaining
sub-mss skb (assuming MTU=1500)

This makes slow start suboptimal because many small frames are sent to
qdisc/driver layers instead of big ones (constrained by cwnd and packets
in flight of course)

In fact, applications using sendmsg() (adding an additional memory copy)
instead of vmsplice()/splice()/sendfile() are a bit faster because of
this anomaly, especially if serving small files in environments with
large initial [c]wnd.

Call tcp_push() only if MSG_MORE is not set in the flags parameter.

This bit is automatically provided by splice() internals but for the
last page, or on all pages if user specified SPLICE_F_MORE splice()

In some workloads, this can reduce number of sent logical packets by an
order of magnitude, making zero-copy TCP actually faster than
one-copy :)

Reported-by: Tom Herbert <>
Cc: Nandita Dukkipati <>
Cc: Neal Cardwell <>
Cc: Tom Herbert <>
Cc: Yuchung Cheng <>
Cc: H.K. Jerry Chu <>
Cc: Maciej Żenczykowski <>
Cc: Mahesh Bandewar <>
Cc: Ilpo Järvinen <>
Signed-off-by: Eric Dumazet <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoppp: Don't stop and restart queue on every TX packet
David Woodhouse [Wed, 25 Apr 2012 02:09:47 +0000 (22:09 -0400)]
ppp: Don't stop and restart queue on every TX packet

[ This combines upstream commit
  e675f0cc9a872fd152edc0c77acfed19bf28b81e and follow-on bug fix
  commit 9a5d2bd99e0dfe9a31b3c160073ac445ba3d773f ]

For every transmitted packet, ppp_start_xmit() will stop the netdev
queue and then, if appropriate, restart it. This causes the TX softirq
to run, entirely gratuitously.

This is "only" a waste of CPU time in the normal case, but it's actively
harmful when the PPP device is a TEQL slave — the wakeup will cause the
offending device to receive the next TX packet from the TEQL queue, when
it *should* have gone to the next slave in the list. We end up seeing
large bursts of packets on just *one* slave device, rather than using
the full available bandwidth over all slaves.

This patch fixes the problem by *not* unconditionally stopping the queue
in ppp_start_xmit(). It adds a return value from ppp_xmit_process()
which indicates whether the queue should be stopped or not.

It *doesn't* remove the call to netif_wake_queue() from
ppp_xmit_process(), because other code paths (especially from
ppp_output_wakeup()) need it there and it's messy to push it out to the
other callers to do it based on the return value. So we leave it in
place — it's a no-op in the case where the queue wasn't stopped, so it's
harmless in the TX path.

Signed-off-by: David Woodhouse <>
Signed-off-by: David S. Miller <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agolockd: fix the endianness bug
Al Viro [Fri, 13 Apr 2012 17:49:47 +0000 (13:49 -0400)]
lockd: fix the endianness bug

commit e847469bf77a1d339274074ed068d461f0c872bc upstream.

comparing be32 values for < is not doing the right thing...

Signed-off-by: Al Viro <>
Cc: "J. Bruce Fields" <>
Cc: Trond Myklebust <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoocfs2: ->e_leaf_clusters endianness breakage
Al Viro [Fri, 13 Apr 2012 16:30:02 +0000 (12:30 -0400)]
ocfs2: ->e_leaf_clusters endianness breakage

commit 72094e43e3af5020510f920321d71f1798fa896d upstream.

le16, not le32...

Signed-off-by: Al Viro <>
Cc: Mark Fasheh <>
Cc: Joel Becker <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoocfs2: ->rl_count endianness breakage
Al Viro [Fri, 13 Apr 2012 16:28:21 +0000 (12:28 -0400)]
ocfs2: ->rl_count endianness breakage

commit 28748b325dc2d730ccc312830a91c4ae0c0d9379 upstream.

le16, not le32...

Signed-off-by: Al Viro <>
Cc: Mark Fasheh <>
Cc: Joel Becker <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoocfs: ->rl_used breakage on big-endian
Al Viro [Fri, 13 Apr 2012 16:27:11 +0000 (12:27 -0400)]
ocfs: ->rl_used breakage on big-endian

commit e1bf4cc620fd143766ddfcee3b004a1d1bb34fd0 upstream.

it's le16, not le32 or le64...

Signed-off-by: Al Viro <>
Cc: Mark Fasheh <>
Cc: Joel Becker <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoocfs2: ->l_next_free_req breakage on big-endian
Al Viro [Fri, 13 Apr 2012 16:22:00 +0000 (12:22 -0400)]
ocfs2: ->l_next_free_req breakage on big-endian

commit 3a251f04fe97c3d335b745c98e4b377e3c3899f2 upstream.

It's le16, not le32...

Signed-off-by: Al Viro <>
Cc: Mark Fasheh <>
Cc: Joel Becker <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agobtrfs: btrfs_root_readonly() broken on big-endian
Al Viro [Fri, 13 Apr 2012 15:49:04 +0000 (11:49 -0400)]
btrfs: btrfs_root_readonly() broken on big-endian

commit 6ed3cf2cdfce4c9f1d73171bd3f27d9cb77b734e upstream.

->root_flags is __le64 and all accesses to it go through the helpers
that do proper conversions.  Except for btrfs_root_readonly(), which
checks bit 0 as in host-endian...

Signed-off-by: Al Viro <>
Cc: Chris Mason <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agonfsd: fix compose_entry_fh() failure exits
Al Viro [Fri, 13 Apr 2012 04:32:14 +0000 (00:32 -0400)]
nfsd: fix compose_entry_fh() failure exits

commit efe39651f08813180f37dc508d950fc7d92b29a8 upstream.

Restore the original logics ("fail on mountpoints, negatives and in
case of fh_compose() failures").  Since commit 8177e (nfsd: clean up
readdirplus encoding) that got broken -
rv = fh_compose(fhp, exp, dchild, &cd->fh);
if (rv)
       goto out;
if (!dchild->d_inode)
goto out;
rv = 0;
is equivalent to
rv = fh_compose(fhp, exp, dchild, &cd->fh);
and the second check has no effect whatsoever...

Signed-off-by: Al Viro <>
Cc: "J. Bruce Fields" <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agort2x00: Identify rt2800usb chipsets.
Gertjan van Wingerde [Wed, 28 Dec 2011 00:53:18 +0000 (01:53 +0100)]
rt2x00: Identify rt2800usb chipsets.

commit bc93eda7e903ff75cefcb6e247ed9b8e9f8e9783 upstream.

According to the latest USB ID database these are all RT2770 / RT2870 / RT307x

Signed-off-by: Gertjan van Wingerde <>
Acked-by: Ivo van Doorn <>
Signed-off-by: John W. Linville <>
Cc: Ben Hutchings <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agort2800: Add support for the Fujitsu Stylistic Q550
Alan Cox [Mon, 19 Dec 2011 21:07:33 +0000 (21:07 +0000)]
rt2800: Add support for the Fujitsu Stylistic Q550

commit 3ac44670ad0fca8b6c43b3e4d8494c67c419f494 upstream.

Just another USB identifier.

Signed-off-by: Alan Cox <>
Acked-by: Gertjan van Wingerde <>
Signed-off-by: John W. Linville <>
Cc: Ben Hutchings <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agort2x00: Add USB device ID of Buffalo WLI-UC-GNHP.
Gertjan van Wingerde [Sat, 12 Nov 2011 18:10:43 +0000 (19:10 +0100)]
rt2x00: Add USB device ID of Buffalo WLI-UC-GNHP.

commit c18b7806e4f3373b2f296a65fb19251a3b49a532 upstream.

This is reported to be an RT3070 based device.

Reported-by: Teika Kazura <>
Signed-off-by: Gertjan van Wingerde <>
Acked-by: Ivo van Doorn <>
Signed-off-by: John W. Linville <>
Cc: Ben Hutchings <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agort2800usb: Add new device ID for Belkin
Eduardo Bacchi Kienetz [Sun, 10 Jul 2011 15:05:14 +0000 (17:05 +0200)]
rt2800usb: Add new device ID for Belkin

commit 43bf8c245237b8309153aa39d4e8f1586cf56af0 upstream.

Belkin's Connect N150 Wireless USB Adapter, model F7D1101 version 2, uses ID 0x945b.
Chipset info: rt: 3390, rf: 000b, rev: 3213.
I have just bought one, which started to work perfectly after the ID was added through this patch.

Signed-off-by: Eduardo Bacchi Kienetz <>
Acked-by: Gertjan van Wingerde <>
Signed-off-by: Ivo van Doorn <>
Signed-off-by: John W. Linville <>
Cc: Ben Hutchings <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agort2x00: Properly identify rt2800usb devices.
Gertjan van Wingerde [Wed, 6 Jul 2011 20:59:19 +0000 (22:59 +0200)]
rt2x00: Properly identify rt2800usb devices.

commit acb56120d2c386d6dd104a6515c1a15dabc1ef87 upstream.

Sitecom WLA4000 (USB ID 0x0df6:0x0060) is an RT3072 chipset.
Sitecom WLA5000 (USB ID 0x0df6:0x0062) is an RT3572 chipset.

Signed-off-by: Gertjan van Wingerde <>
Signed-off-by: Ivo van Doorn <>
Signed-off-by: John W. Linville <>
Cc: Ben Hutchings <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agospi: Fix device unregistration when unregistering the bus master
Laurent Pinchart [Mon, 12 Dec 2011 00:15:06 +0000 (01:15 +0100)]
spi: Fix device unregistration when unregistering the bus master

commit 178db7d30f94707efca1a189753c105ef69942ed upstream.

Device are added as children of the bus master's parent device, but
spi_unregister_master() looks for devices to unregister in the bus
master's children. This results in the child devices not being

Fix this by registering devices as direct children of the bus master.

Signed-off-by: Laurent Pinchart <>
Signed-off-by: Grant Likely <>
Cc: Takahiro AKASHI <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoDon't limit non-nested epoll paths
Jason Baron [Fri, 16 Mar 2012 20:34:03 +0000 (16:34 -0400)]
Don't limit non-nested epoll paths

commit 93dc6107a76daed81c07f50215fa6ae77691634f upstream.

Commit 28d82dc1c4ed ("epoll: limit paths") that I did to limit the
number of possible wakeup paths in epoll is causing a few applications
to longer work (dovecot for one).

The original patch is really about limiting the amount of epoll nesting
(since epoll fds can be attached to other fds). Thus, we probably can
allow an unlimited number of paths of depth 1. My current patch limits
it at 1000. And enforce the limits on paths that have a greater depth.

This is captured in:

Signed-off-by: Jason Baron <>
Cc: Andrew Morton <>
Signed-off-by: Linus Torvalds <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoBluetooth: Add support for Atheros [04ca:3005]
AceLan Kao [Wed, 28 Mar 2012 02:25:36 +0000 (10:25 +0800)]
Bluetooth: Add support for Atheros [04ca:3005]

commit 55ed7d4d1469eafbe3ad7e8fcd44f5af27845a81 upstream.

Add another vendor specific ID for Atheros AR3012 device.
This chip is wrapped by Lite-On Technology Corp.

output of usb-devices:
T:  Bus=04 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3005 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Signed-off-by: AceLan Kao <>
Signed-off-by: Gustavo Padovan <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoext4: fix endianness breakage in ext4_split_extent_at()
Al Viro [Fri, 13 Apr 2012 00:32:25 +0000 (20:32 -0400)]
ext4: fix endianness breakage in ext4_split_extent_at()

commit af1584f570b19b0285e4402a0b54731495d31784 upstream.

->ee_len is __le16, so assigning cpu_to_le32() to it is going to do
Bad Things(tm) on big-endian hosts...

Signed-off-by: Al Viro <>
Cc: Ted Ts'o <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agoPCI: Add quirk for still enabled interrupts on Intel Sandy Bridge GPUs
Thomas Jarosch [Wed, 7 Dec 2011 21:08:11 +0000 (22:08 +0100)]
PCI: Add quirk for still enabled interrupts on Intel Sandy Bridge GPUs

commit f67fd55fa96f7d7295b43ffbc4a97d8f55e473aa upstream.

Some BIOS implementations leave the Intel GPU interrupts enabled,
even though no one is handling them (f.e. i915 driver is never loaded).
Additionally the interrupt destination is not set up properly
and the interrupt ends up -somewhere-.

These spurious interrupts are "sticky" and the kernel disables
the (shared) interrupt line after 100.000+ generated interrupts.

Fix it by disabling the still enabled interrupts.
This resolves crashes often seen on monitor unplug.

Tested on the following boards:
- Intel DH61CR: Affected
- Intel DH67BL: Affected
- Intel S1200KP server board: Affected
- Asus P8H61-M LE: Affected, but system does not crash.
  Probably the IRQ ends up somewhere unnoticed.

According to reports on the net, the Intel DH61WW board is also affected.

Many thanks to Jesse Barnes from Intel for helping
with the register configuration and to Intel in general
for providing public hardware documentation.

Signed-off-by: Thomas Jarosch <>
Tested-by: Charlie Suffin <>
Signed-off-by: Jesse Barnes <>
Signed-off-by: Greg Kroah-Hartman <>
5 years agousb: musb: omap: fix the error check for pm_runtime_get_sync
Shubhrajyoti D [Thu, 22 Mar 2012 07:18:06 +0000 (12:48 +0530)]
usb: musb: omap: fix the error check for pm_runtime_get_sync

commit ad579699c4f0274bf522a9252ff9b20c72197e48 upstream.

pm_runtime_get_sync returns a signed integer. In case of errors
it returns a negative value. This patch fixes the error check
by making it signed instead of unsigned thus preventing register
access if get_sync_fails. Also passes the error cause to the
debug message.

Cc: Kishon Vijay Abraham I <>
Signed-off-by: Shubhrajyoti D <>
Signed-off-by: Felipe Balbi <>
Signed-off-by: Greg Kroah-Hartman <>